• [ Pobierz caÅ‚ość w formacie PDF ]

    Defaults Disabled
    Command Modes Interface configuration
    Command History Release Modification
    10.0 This command was introduced.
    Examples The following example enables the sending of ICMP Mask Reply messages on Ethernet interface 0:
    interface ethernet 0
    ip address 131.108.1.0 255.255.255.0
    ip mask-reply
    Network Protocols Command Reference, Part 1
    P1R-146
    IP Services Commands
    ip mtu
    ip mtu
    To set the maximum transmission unit (MTU) size of IP packets sent on an interface, use the ip mtu
    interface configuration command. To restore the default MTU size, use the no form of this command.
    ip mtu bytes
    no ip mtu
    Syntax Description bytes MTU in bytes.
    Defaults Minimum is 128 bytes; maximum depends on interface medium.
    Command Modes Interface configuration
    Command History Release Modification
    10.0 This command was introduced.
    Usage Guidelines If an IP packet exceeds the MTU set for the interface, the Cisco IOS software will fragment it.
    All devices on a physical medium must have the same protocol MTU in order to operate.
    Note Changing the MTU value (with the mtu interface configuration command) can affect the
    IP MTU value. If the current IP MTU value is the same as the MTU value, and you change
    the MTU value, the IP MTU value will be modified automatically to match the new MTU.
    However, the reverse is not true; changing the IP MTU value has no effect on the value for
    the mtu command.
    Examples The following example sets the maximum IP packet size for the first serial interface to 300 bytes:
    interface serial 0
    ip mtu 300
    Related Commands Command Description
    mtu Adjusts the maximum packet size or MTU size.
    Network Protocols Command Reference, Part 1
    P1R-147
    IP Services Commands
    ip redirects
    ip redirects
    To enable the sending of ICMP Redirect messages if the Cisco IOS software is forced to resend a packet
    through the same interface on which it was received, use the ip redirects interface configuration
    command. To disable the sending of redirect messages, use the no form of this command.
    ip redirects
    no ip redirects
    Syntax Description This command has no arguments or keywords.
    Defaults Enabled, unless Hot Standby Router Protocol is configured
    Command Modes Interface configuration
    Command History Release Modification
    10.0 This command was introduced.
    Usage Guidelines If the Hot Standby Router Protocol is configured on an interface, ICMP Redirect messages are disabled
    by default for the interface.
    Examples The following example enables the sending of ICMP Redirect messages on Ethernet interface 0:
    interface ethernet 0
    ip redirects
    Related Commands Command Description
    ip default-gateway Defines a default gateway (router) when IP routing is disabled.
    show ip redirects Displays the address of a default gateway (router) and the address of hosts
    for which an ICMP Redirect message has been received.
    Network Protocols Command Reference, Part 1
    P1R-148
    IP Services Commands
    ip source-route
    ip source-route
    To allow the Cisco IOS software to handle IP datagrams with source routing header options, use the
    ip source-route global configuration command. To have the software discard any IP datagram
    containing a source-route option, use the no form of this command.
    ip source-route
    no ip source-route
    Syntax Description This command has no arguments or keywords.
    Defaults Enabled
    Command Modes Global configuration
    Command History Release Modification
    10.0 This command was introduced.
    Examples The following example enables the handling of IP datagrams with source routing header options:
    ip source-route
    Related Commands Command Description
    ping (privileged) Diagnoses basic network connectivity on Apollo, AppleTalk,
    Connectionless Network Service (CLNS), DECnet, IP, Novell IPX, VINES,
    or XNS networks.
    ping (user) Diagnoses basic network connectivity on AppleTalk, CLNS, IP, Novell,
    Apollo, VINES, DECnet, or XNS networks.
    Network Protocols Command Reference, Part 1
    P1R-149
    IP Services Commands
    ip tcp chunk-size
    ip tcp chunk-size
    To alter the TCP maximum read size for Telnet or rlogin, use the ip tcp chunk-size global configuration [ Pobierz całość w formacie PDF ]

  • zanotowane.pl
  • doc.pisz.pl
  • pdf.pisz.pl
  • matkadziecka.xlx.pl